Checklist for Furnace Maintenance

As winter approaches in Kansas City and temperatures start to drop, it’s time to start thinking about furnace maintenance. After all, you don’t want your furnace to break down in the middle of a cold snap!

Points for Furnace Maintenance:

Here at Delta T Heating and Cooling, we’re experts in furnace maintenance and furnace repair in Kansas City. We’ve put together this handy checklist to help you make sure your furnace is ready for winter:

Air Filter

An air filter helps to remove dust, dirt, and other airborne particles from the air that circulates through your furnace. A clean air filter is essential for efficient furnace operation, so make sure to change it every 1-2 months to ensure efficient operation.

Lubricate Blower, Fans, and Other Moving Parts:

Blowers and fans are the moving parts in your furnace that circulate air. Lubricating these parts help to keep them operating smoothly and prevents them from overheating.

Furnace Burner:

The furnace burner is the part of the furnace that actually burns fuel (usually natural gas or propane) to create heat. Over time, the burner can become dirty, which can cause furnace problems. It should be cleaned to remove any built-up dirt or debris.

Furnace pilot light:

The furnace pilot light is a small flame that ignites the furnace burner. If the furnace pilot light goes out, the furnace will not operate.

Next, the color of the pilot light should be blue. If it’s not, there may be a problem with the furnace.

Electrical Connections

The heating system’s electrical connections should be checked yearly to ensure they are tight and free of any corrosion during the heating maintenance. 

Heat Exchanger

The furnace heat exchanger is responsible for heating the air. Over time, the heat exchanger can become cracked or damaged, which can be a safety hazard. If you see any, the heat exchanger will need a repair or replacement.

Connections to Gas or Oil Lines

If your furnace is powered by gas or oil, it will have connections to gas or oil lines. These connections can become loose over time, which can lead to safety hazards.

System Controls

The furnace system controls are the parts of the furnace that control the furnace operation. Over time, these controls can become worn or damaged, which can cause furnace problems.

Carbon Monoxide Levels

If your furnace is producing carbon monoxide, it can be a safety hazard. Use a carbon monoxide detector to test the air near the furnace. If the carbon monoxide levels are high, call us for furnace maintenance. So contact HVAC Companies in Kansas City to resolve your problems related to furnace and HVAC.


The furnace thermostat is the part of the furnace that controls the furnace temperature. Over time, the thermostat can become inaccurate, which can cause furnace problems.


If your furnace has a humidifier, it is crucial to check it yearly to make sure it is working properly. A humidifier can help to increase the comfort level in your home by adding moisture to the air. However, if the humidifier isn’t working properly, it can actually do more harm than good.

Now that you know what furnace maintenance tasks to complete, it’s time to get started! Schedule heating services in Kansas City with Delta T Heating and Cooling today to ensure your furnace is ready for winter. Give us a call at (913)-687-1494.

Seven Furnace Efficiency Tips To Save Energy

As the weather cools down, you find yourself spending more time indoors, and therefore, even end up using more energy as a result. Furnace efficiency is most important for enjoying a warm and comfortable stay indoors, especially in the coming months. 

Delta T Heating & Cooling Providing heating services in Kansas City and surrounding areas. It is essential to be smart in energy spending and smarter as the mercury dips outside. We have enumerated seven furnace efficiency tips, which could save you a lot of energy and money. 

Seven Tips To Save Energy This Winter:

  • Clean and Change Your Air Filters:

Since furnaces are used so actively in winters, the filters of your furnaces can get clogged with dust and dirt, thereby reducing the amount of warm air reaching inside your house. That will lead you to raise the temperatures of your heating systems, which will be a reason for higher electricity bills. Check your filters regularly and clean them every month. It is essential to change your filters at least every three months. 

  • Don’t Block The Air Vents:

Take a look around your house and check if there are any obstructions near your air vents. Remove any unwanted furniture or drapes that could block warm air coming from your furnace. Vacuum the vents opening to keep them clean and free of dust or dirt. 

  • Switch To a Smart Thermostat:

A smart thermostat is a smart way to save electricity in the winter. Programmable thermostats allow you to fine-tune and optimize your furnace as required. You can also program the thermostat to turn down when you are asleep or away and then set it warmer for just before your arrival back home. In winter, you can reduce your electricity bill by spending a little on a smart thermostat. 

  • Put on Your Woolens:

On days when it gets extremely cold, instead of just raising the temperature of your thermostat, it will be better to put on some warm clothes to feel comfortable indoors. Warmer clothing will save your energy as well as money. 

  • Weatherstrip Doors and Windows:

Most of the warm air in the house is lost through the gaps and crevices on doors and windows. You can put a stop to it by weatherstripping them. Additionally, door sweeps and draft stoppers can stop air from leaking out and give you some protection from the cold.

  • Upgrade Your Furnace:

Older furnaces usually have a lesser efficiency range than newer ones. Studies show that modern high-efficiency heating systems can provide up to 90%-95% efficiency. Buying a new model might also get you some offers and rebates and help you cut down on your energy bills. You must contact a certified furnace replacement in Kansas City, KS, for assistance in this regard. 

  • Get Regular Furnace Maintenance:

One of the surest ways to reduce your energy bills is to call for HVAC maintenance before the onset of winters. Getting your furnaces inspected by HVAC professionals will increase their efficiency and lifespan. 

We’re here to help!

If you are looking for a reliable furnace repair in Kansas City, KS – feel free to contact Delta T Heating and Cooling. Our qualified team will help you keep your home warmer. Just visit our website or give a call on (913) 687 1494

Why Is My Heat Pump Not Working?

Heat pumps are one of the most amazing inventions meant for our comfort. Unlike other HVAC systems, a heat pump can provide cooling and heating. However, like most machines, a heat pump can break down at any time. Nothing can be awful than a heat pump not blowing cold air on a hot sunny day!

There can be various reasons behind clogged air filters to malfunctioning thermostats. Before you contact a heat pump repair Kansas City, look at some of the most common reasons.

5 Reasons Your Heat Pump is Not Working

  • Power Issues

If your heat pump stops suddenly, check the power supply of your other heat pump system components. Each component might have its own power switches and dedicated circuits.

Firstly, check if the power switch near the indoor unit is ON. Secondly, the power switch located on the outside unit also needs to be set to ON. At last, go to your home’s electrical panel to examine the circuits controlling both the indoor and outdoor units.

If you see any tripped breaker or a blown-out fuse, call professional furnace replacement Kansas City KS.

  • Malfunctioning Thermostat

When heat pumps stop working, a malfunctioning thermostat can be the culprit. Locate the thermostat and see if the display is on or not. If it doesn’t display anything, it means there is no power supply.

However, if you have battery-powered units, just replace old batteries with new ones. While for the hardwired units, check your home’s electrical panel as mentioned above. 

  • Wrong Thermostat Settings

Apart from the disrupted power supply and dead batteries, a thermostat can go bad simply due to the wrong settings. Your thermostat only allows your heat pump to cool if temperatures inside your home rise above a certain point. Try adjusting the thermostat’s set temperature down several degrees, which should trigger the heat pump to run a cooling cycle.

  • Leaky Ductwork

Ductwork makes up a significant part of an HVAC system responsible for distributing the air. If your home’s ductwork becomes clogged due to a lack of cleaning, the heat pump won’t be able to blow adequate air. At the same time, any leaks will let the air out before reaching you.

In such cases, call professional heating services in Kansas City to examine the ducts for blockage and leaks.

  • Dirty Air Filters

As soon as your heat pump stops working, inspect the air filters. If you see a lot of gunk accumulated on them, it has probably blocked the airflow resulting in a shutdown. If this is the case, replace the filters with fresh ones and let the system cool down for a bit.

If your heat pump has stopped working, there can be one or more reasons listed above. Thankfully, we can fix this issue in no time. We take pride in performing the best heat pump and furnace repairs in Kansas City.

Ring us today at (913) 687-1494 to register and schedule a complete heat pump service at a minimal cost. You deserve the best!

What’s Making My Furnace So Loud, and What Can I Do About It?

It is normal for a furnace to make noise after some time if it’s not properly serviced. But if it makes noise more than usual then it could be a sign of a mysterious threat. Underlying problems in the furnace causing sound may lead to damage to the unit and the area around it.

Different Sounds That Your Furnaces Makes

Different problems will lead to different annoying sounds of the furnace. Loud screeching and rattling sounds could be evidence of a hitch in the blower motor which can be fixed with the assistance of professionals. Crushing of metals, humming, rattling pop and bang, etc. are some babble you may hear due to dirty burner, error in blower wheel, loose or damaged Blower belt.

Cause of These Sounds

Dirty burners can lead to explosions and their underlying problem can be noticed by boom or band sound. Delay in spunk can cause gas to collect and boom when the ignition turns on. To prevent such mishaps burners require annual inspection and cleaning by professionals to keep air and fuel in equilibrium. Sometimes boom sound can also be caused by contraction and expansion of metal ducts. 

If proper action is not taken in time can lead to destruction and furnace replacement in Kansas City, KS can be pricey. We are available to help you with the assistance of technical experts. Electronic and heat appliances require timely amenities and we are here to provide you fair and reliable system services at a reasonable price.

How To Care For Your Furnace?

We are licensed with professional engineers to meet the needs of clients. furnace repair in Kansas City will be cost-efficient with us. We will provide a satisfactory outcome because our name means everything to us. Our clients always provide us with sufficient remarks and reviews. We will provide you with a qualified HVAC technician for a furnace device inspection. 

Sometimes a furnace demands more than just lubrication and oiling. A furnace is a technical unit that will require assistance from professional technical. Fixing the furnace on your own can even lead to further damage to the device and yourself as it is filled with fumes. Furnace damage is not only limited to tightening loose screws or changing a belt. Sometimes, a part of the unit holding crack or leak needed to be replaced, which can be best guided by our professionals.

Neglecting a furnace for a longer period can cause an interchange of fuels in it and will release toxic fumes like carbon monoxide in your home. This usually happens due to declining heat exchanger problems for a long period. The most common problem in furnaces is related to heat and we offer abetment in heat pump repair in Kansas City.

Winters in Kansas City can be cold. Our team provides you services in the HVAC system so in case a problem occurs you can contact us. We are always delighted to help with additional issues such as heating installation, furnace, and heating maintenance, heating system, dependable heating replacement, heating services, thermostats, and more. All you need to go to our website and book a schedule with our professional for assistance of HVAC near you

HVAC For Beginners: Significant The Components and What They All Do

Is It Important To Know The Components Of HVAC Systems?

Heating, ventilation, and air conditioning systems not only regulate the temperature of a space (mostly indoors) but are also responsible for delivering clean air to ensure comfort when required.

Because your system includes various components, knowing about them is quite useful for appreciating the quality of their construction and mapping out what your system may need to perform as you would like. Let’s understand the components and their uses in brief.


Temperature sensors on thermostats tell them when to turn on or off the heater or air conditioner. Different thermally controlled zones could exist, each needing its thermostat. 

It would help if you positioned the thermostat at least two meters away from areas where temperature differences are concentrated compared to the average temperature of the intended space. If you need services of HVAC near you. contact us.

Heat Generator

When it comes to heating, the heat generator is the most important HVAC component. Fuel is burned inside combustion chambers to produce heat, like in a furnace. 

Flue gas heat will then be transferred to nearby air or another fluid, such as water, to heat the air in the conditioned environment. It is also possible to heat the air by using electric heat generation. Schedule a heat pump repair in Kansas city with Delta T Heating.


Blowers are responsible for forcing air through the heat exchanger into the air ducting to take the warm air to its destination. Powered by an electric motor, a shaft drives the blower. By changing the motor speed, you can adjust the flow of air. Variable speed motors are recommended for such applications.

Condenser Coil Or Compressor

The compressor or condenser coil is usually located outdoors, and it is one of the key components of the HVAC system. Upon warming up, the refrigerant gas goes to the compressor and becomes liquid in the atmosphere. The liquid refrigerant is transported by copper or aluminum tubes. A fan will increase airflow, thereby increasing condensation.

Evaporator Coil

Evaporator coils are among the indoor components of HVAC systems that receive condensed liquid refrigerant from the compressor. A spray nozzle atomizes the liquid refrigerant, causing it to evaporate faster when it has contact with the warm air present in a room.

Air Ducts And Vents

Different components of the HVAC system receive air via ducts. For a zone to receive high-quality air, ducting must be of good quality. The system could make noise if there is a leak in the ductwork. If the air ducts are in bad condition, odors and excess moisture can fill the air.

Heat Exchanger

Heating and air conditioning systems include heat exchangers that convert heat from heat generation units into other fluids. Control units may activate the heater or electric heating elements to regulate the air temperature passing through a heat exchanger.

Call (913 687-1494) or schedule a furnace repair in Kansas City with Delta T Heating and Cooling. We also provide heating services in Kansas City and surrounding areas.

What Happens During An Air Conditioning Repair Service?

What Can You Expect During An Air Conditioning Repair Service?

A modern Air Conditioner has a life of 15-20 years; in all these years of service, it is necessary to get your AC repaired at regular intervals, usually once a year. And if you live in the hot and humid city of Kansas, where AC is a large part of lifestyle and comfort, it becomes more critical. But what does an air conditioner repair in Kansas City include? That’s precisely what we are going to talk about in this article! Read on to know.

Cleaning And Checking Up

While working, the AC takes in the dust in the atmosphere, and it gets deposited in the pipes/tubes inside the unit, which can lead to water leakage. These leakages are the first thing technicians inspect in a unit; the deposited dust and debris are cleaned to fix this.

Cleaning Fin and Air Filter

Fin allows the air to flow smoothly throughout the unit and a filter’s job is to keep the air clean by catching pollutants. However, the deposition of mold and debris can lead to ice formation. That’s why it is necessary to clean the fan and filters so that the unit works efficiently.

The Evaporator And Condenser Coils Are Cleaning

The evaporator coils collect the heat from the indoor, and the condenser coils let this heat out. This function is crucial to the proper functioning of the entire AC unit, and it can’t be done correctly if the coils are jammed with dust and debris. Therefore, other essential AC fans are also cleaned in an AC tune-up in Kansas City, KS.

Testing Coolant Level

A coolant takes away the heat from the refrigerated area and produces a cooling effect. A drop in the coolant level, lower than the average level, affects the overall cooling and may cause your AC to stop.

Cleaning Condensate Pan

The moisture from the evaporator coils is collected in the condensate pan, then removed by a drain. This can sometimes lead to clogging if it is not appropriately cleaned at regular intervals.

Checking The Thermostat

A thermostat maintains the temperature and makes sure that your home gets the perfect cooling experience. These are usually of two kinds – Electronic and Electromechanical. If your thermostat keeps switching on and off or shows incorrect readings, or is old, then it may require servicing. If you need AC replacement in Kansas City, contact us.

All-Around Inspection

All around inspection includes checking all the other components and devices that contribute to the proper functioning of an AC unit. This includes:

  1. Inspection of and fixing all the faulty electric connections, writings, switches, capacitors, and relays.
  2. Lubricating and cleaning the motors and fans.
  3. Efficiency and safety checks.

AC repairing usually takes a couple of hours, which can make your AC more efficient. To ensure this, you need only the best AC service in Kansas City, KS. Delta T Heating and Cooling are perfect for your AC! We provide the best customer service at reasonable prices. Contact us (913) 687-1494 or drop a mail at [email protected] to avail of a service. 

Eight Reasons Why There Isn’t Enough Airflow From Your A/C

When the temperature is warm, homeowners understand how important it is to have a functioning air conditioner. So, what should you do if your air conditioner stops working unexpectedly? Airflow difficulties are one of the most typical HVAC difficulties. You will have to call for an AC service in Kansas City, KS.

Listed below are symptoms of a failing AC: 

  • There are hot and chilly areas.
  • Unbalanced pressure.
  • There is no air coming out.
  • The air conditioner blows warm air.

Following Factors Could Be The Reason For Low Airflow  

  • Obstructed Condenser Unit

A condensing unit normally placed outdoors or in a wiring closet is used in air-cooled air conditioning systems. Leaves and trash that have gathered around the unit might impede outdoor units in particular. When there isn’t enough ventilation in the air conditioning unit, your system might overheat.

  • Duct Leaks

Your HVAC system should be tightly enclosed, with the outputs and outlets around your home serving as the only points of entry and escape. You begin to leak air and lose airflow when your valves are broken by holes, spaces in fittings, and other failures. This makes it more difficult for air to pass through the system. Make an appointment for air conditioner repair in Kansas City to assist you.

  • Dirty filters

That filter has a vital role: it filters the air and keeps dust particles out of your equipment and ducting. If a clogged filter obstructs your HVAC airflow, you’ll notice hot and cold areas and stuffy air. Debris in the apparatus can also cause harm to components.

  • Thermostat issues

HVAC airflow issues can sometimes be caused by anything as simple as a broken thermostat, which will require AC service in Kansas City, KS. Make certain the air conditioner is set to a lower temperature than the inside temperature.

  • Broken fan

Blower fans in your HVAC system transport air down your ducts and across your area. The fan can get covered with filth in some circumstances, slowing the operation and reducing airflow. Fortunately, cleaning the fan is a simple task. If you want to go for a new AC installation in Kansas City, contact us.

  • Unclean coils

The condenser coil on your ac unit does another important job: it releases the heat that has been extracted from your room. Because the coil is part of the outside unit and is subject to the weather, it might get so filthy that it can no longer emit heat.

  • Low refrigerant

Among the most prevalent issues with HVAC systems, particularly older ones that haven’t had enough AC tune-up in Kansas City, KS is this. You’ll notice airflow concerns as well as lower conditioning if your air conditioner is leaking refrigerant. To get things back up and running, your HVAC professional can check for leaks and repair them.

  • Outdated system

The age factor also contributes to how your AC functions. If your AC is older than 12-15 years, depending on how well you’ve kept it with AC tune-up it is bound to go off.

Delta T Heating and Cooling is your one-stop destination for affordable and quality HVAC services from trained technicians. Call us, or send an email at [email protected].

Why An Electrical Panel Replacement Is Worth It

Once an electrical panel that has been installed in your house gets old, the thought of upgrading or replacing it is a lingering one. But this is not easy on the pocket. There is always a certain hesitation about the replacement being worth the cost. If you are contemplating the same, you’re in luck! You can go through this article and then make up your mind accordingly.

Looking for an electrician in Kansas CityDelta T Heating and Cooling provide the best and most efficient services in the entirety of Kansas City. With affordable packages and only the best professional technicians working in and around your home, rest assured you can leave your house repairs duties in our hands.

Is an upgrade or replacement worth it?

As you look at upgrading your electrical panel, you’re often in doubt due to the high costs. The cost of upgrading an electrical panel is not pocket-friendly at all. The overall cost of replacing the electrical panel is also extremely expensive. But it is the need of the hour. Here’s why:

A heavier load capacity is needed in modern homes

If your home is older, there is a high chance that electric-powered devices and appliances that are more than the standard when the house was originally built are currently used. So, your house’s electrical system may have problems with a heavier load that is caused due to these electric devices or appliances. A heavier than normal load will cause your breakers to trip frequently while using your appliances or devices and prevent you from using your electrical appliances with ease.

Protection from unwarranted electrical fires

An old electrical panel puts you and your family at a higher risk of getting caught in an electrical fire. Your house can be in danger in such cases. An electrical fire, while causing deaths, can also ruin your house and put all your belongings at extreme risk. Replacing your outdated electrical panel is the smart thing to do. While doing so, a thorough check must also be done of the entire house’s wiring so that your house’s electrical system is completely safe.

A better electrical panel increases the resale value of your home

Increasing and maintaining the value of your house is every single homeowner’s priority. Upgrading the electrical panel of your house boosts the value of your house and makes it more appealing. If you decide to put your house on the market for sale, this upgrade could help you get a good amount for your house. An upgraded electrical panel will help you boost the sales of your house if you decide on selling it in the future.

For affordable electrical contractors in Kansas CityDelta T Heating and Cooling is the top choice. With professional HVAC Contractor Kansas City, they provide only the best services to make your home a better place to live in. Contact Delta T Heating and Cooling today and get started with your home repair processes!

5 Common Springtime AC Problems

Spring is almost around the corner. After a long break, it’s time for your AC to start working non-stop again. While you might be lucky that it still works without a hassle, there is a good chance that it may face some issues after being idle for so long. So, it’s better to get a maintenance check and make sure that your AC is working fine and let professional technicians help you out with your air conditioner repair in Kansas City.

Most Common Springtime AC Problems

Spring brings in several issues with your air conditioning unit. Here 5 of the most common springtime problems that may crop up:

  • Dirty air filter

Air filters must be cleaned or replaced at least every two months, depending on your model and usage. A dirty air filter can cause a lot of problems like restricted airflow, low cooling, high power usage, unusual buzzing, and even a bad smell.

  • Refrigerant leak

The simplest way to pick out a refrigerant leak is when your air conditioner is just blowing air without cooling it. This is a serious issue if not dealt with immediately. Apart from causing high electricity bills, low cooling, and damaging your AC, refrigerant gases can also be harmful for the health of your family. It is important to call an expert for AC tune-up in Kansas City to make your necessary changes done.

  • Thermostat fault

When the season changes, sometimes the thermostat setting has to be changed from heating to a cooling mode. Even if it is an automatic thermostat and your home temperature still feels uncomfortable, there may be some issues. You could try and recalibrate it using the manufacturer’s instruction manual. If the problem persists, contact experts for AC installation in Kansas City.

  • Air leak

Heavy winter conditions tend to create duct leaks that result in the leaking of cooled air. This could be due to the crack in your windows or doors that can cause cool air to leak outside. You will technically be paying for cooling the outside of your home. Make sure to seal these gaps using sealant or weather stripping to save your money.

  • Clogged drain pipe

Your AC cools humid air from the outside and separates the moisture before it enters your home. This moisture goes out through the drain pipe. Since your AC is out for a long time, things like algae or dust particles get settled. Make sure to contact Delta T Heating and Cooling, the best AC repair for required services.

While these are the most common issues you may face after restarting your AC after a long time, these are not the only ones. For the safety of your air conditioner, we highly recommend you get a maintenance check before turning on your air conditioner. If you ever doubt that your AC is leaking refrigerant, contact Delta T Heating and Cooling services for AC repair.

For all your HVAC needs, reach out at Delta T, the most reliable AC service in Kansas City, KS. Contact us by calling at (913)687-1494 for more details.